-
Description
Development based on nylon 6/66 copolymer; Self-lubricating wear resistance makes it suitable for printing gears; High toughness and impact resistance, with an elongation at break of up to 175%, which can print strong and durable parts with high fracture resistance; Low shrinkage, not easy to warp and crack when printing.Sellingpoint
High toughness High impact resistanceSelf-lubricating wear-resisting Excellent printability
Add to Wishlist
Add to Wishlist
-
Description
PVA+ is a water-soluble material that is often used as a support material with no need of adding any chemical and speicial treating. Leave the part in a warm water bath dissolve faster. After dissolution, there is no residue on the model surface with smoothy effect; it can be worked with PLA, TPU, PA(nylon) and other consumables materials to print extremely complex shapes or support materials with a partially closed cavity model. It’s also a good choice to work for multi-nozzle printers.Sellingpoint
Water soluble.Support material.
Add to Wishlist
Add to Wishlist
-
Description
This dissolvable filament can be used as a 3D printing support material when printing such as ABS, PETG, etc.extremely complex shapes or shapes with partially closed cavities; Hips filament is suitable for multi-nozzle printers.Sellingpoint
Solubility Support Heat resistanceHigh toughness High impact resistance
Add to Wishlist
Add to Wishlist
Description
Foaming makes the layered pattern almost invisible, and the surface of the printed item is matte and delicate. Under the same model and at the same speed, the Light weight pla filament enables the model aircraft to have a lighter wing load and a lower stall speed, which can greatly improve the performance of the model aircraft.
Sellingpoint
Density as low as 0.54g/cm3
Foaming volume ratio 220%
Free adjustment of strength and foaming ratio
Excellent matte surface effect
Good interlayer adhesion
Easy to paint
Excellent printability
Tips
Notes
1. Note that the first layer speed setting is consistent with the actual printing speed, set to 100% of the actual printing speed, turn off the first layer and small area printing speed reduction function, the first layer extrusion rate is consistent with the actual foaming extrusion rate, such as 270 degrees set to 45% of the first layer extrusion rate; if the bed adhesion is too strong, you can set the bottom valve when printing.
2. Pay attention to the maximum operating temperature of the printer. Most Teflon tube printers cannot be operated for a long time above 250℃. Long-term printing above this temperature may cause blocking. If the temperature exceeds 250℃, high temperature printers such as metal hoses are required for printing.
3. Yellowing of printed parts after high temperature foaming is a normal phenomenon. Lowering the printing temperature can relieve it.
4. Since the ePLA-LW foams continuously in the melting cavity of the high-temperature nozzle, the retraction basically does not work. Stringing is normal during printing. It is recommended to print the rc plane in vase mode to reduce the effect of stringing.
5. Foaming ratio is related to temperature, printing speed, nozzle melting cavity size, pay attention to compare model design wall thickness according to your own printing situation, adjust extrusion rate, temperature, speed and other parameters.
Add to Wishlist
Add to Wishlist
-
Description
The strongest pla filament's toughness is better than PETG, and it has good printability nad toughness of PLA, suitable for printing mechanical parts with toughness and precision requirements.Sellingpoint
High impact resistance Better Toughness than PETG Excellent printabilityExcellent printability
Add to Wishlist
Add to Wishlist
-
Description
Development based on nylon 6/66 copolymer; Self-lubricating wear resistance makes it suitable for printing gears; High toughness and impact resistance, with an elongation at break of up to 175%, which can print strong and durable parts with high fracture resistance; Low shrinkage, not easy to warp and crack when printing.Sellingpoint
High toughness High impact resistanceSelf-lubricating wear-resisting Excellent printability
Add to Wishlist
Add to Wishlist
-
Description
3D printing materials with excellent mechanical properties, high toughness and impact resistance, stable and durable; temperature resistance, heat distortion temperature up to 80 ℃.Sellingpoint
High toughness High impact resistanceHeat resistance
Add to Wishlist
Add to Wishlist
-
Description
Flexible TPE printing consumables with hardness of 83A are sturdy and durable; Printed models are softer than TPU-95A and eFlex, with delicate and soft hand feeling,also low surface friction.Sellingpoint
Matte surface effect Skin-friendly feel Flexible and soft Sturdy and durableHigh elasticity High tenacity High impact resistance
Add to Wishlist
Add to Wishlist